USC Dominator Black Urethane Bed Liner Kit

Description

USC Dominator® Urethane Black Bed Liner Kit
Urethane-based Dominator Truck Bed Liner features superior coverage, outstanding chalking resistance, easy application and Available Tintable formula option. Dominator sets a new standard in resin technology for unmatched toughness, solvent resistance and durability.
Kit Includes:
(4) 2010-4 Resin,
(4) 2020-8 Activator
(1) Application gun. (covers standard 6-foot truck bed)
Dominators
Part Numbers:
2000.KT1 - Dominator® Urethane Black Truck Bed Liner 120 oz Kit* 1 kit 9.2 lbs
2010.Q01 - Dominator® Black Resin (Part A) 22.5 oz
2020.HP1 - Dominator® Urethane Activator (Part B) 7.5 oz
Mix Ratio:
Thoroughly shake one 2010-4 Resin (Part A).
Pour the entire contents of one (1) 2020-8 Activator into one (1) 2010-4 Resin can (NOTE: the resin can is larger to accommodate the addition of Activator). DO NOT ADD SOLVENT. When you are finished pouring, tightly reaffix the cap on the Resin can and shake for two minutes by hand or one minute on a paint shaker.
Attach a Schutz-style applicator gun to the mixed resin can (NOTE: the siphon tube should nearly reach the bottom of the can. Adjust the tube if necessary) and tighten securely.
Spray entire contents before mixing another quart.
SURFACE PREPARATION:
Prior to sanding, remove all surface contaminants by properly cleaning the truck bed with a wax, grease and silicone remover.
Protect the vehicle from overspray by masking areas that will not be coated.
Remove all rust by grinding or sandblasting. Blow the surface to remove grinding and sandblasting debris.
Sand the truck bed with 40-120 grit sandpaper. Blow the surface to remove sanding dust.
Clean the truck bed with a wax, grease and silicone remover. Allow the truck bed to thoroughly dry.
Prime bare metal areas with SprayMax 2K aerosol epoxy primer #3680032 or any quality corrosion resistant primer.
APPLICATION:
Set spray gun pressure to 60 psi at the applicator gun. Application air pressure can vary from 50-70 psi depending on the temperature and associated viscosity of the mixed bed liner.
Starting at the bulk head of the cab, hold the applicator gun approximately 2 feet from the surface and apply product to coverage and desired texture.
Spray side walls next, followed by truck bed floor and finishing with tail gate.
Check the truck bed for light areas and apply additional product as needed.
Using a clean cloth saturated with solvent, immediately remove overspray from vehicle.
CLEAN UP:
Clean spray equipment immediately after use with reducer. Keep all product containers tightly closed at all times to avoid potential contamination.
Discard containers according to local, state and government regulations.
DELIVERY:
Allow DOMINATOR to dry and cure in a warm and dry area away from debris and weather exposure. Allow 6 to 8 hours before delivering or outside exposure. Allow 72 hours dry time before full use of the vehicle. To speed cure time, DOMINATOR™ can be force-dried at 120°F for 60 minutes.
TOUCH UP OR REPAIR:
DOMINATOR can be “touched up” the same day without sanding. If the sprayed material has dried for more than one day, sand the repair area and adjacent areas to ensure adhesion.
TECHNICAL INFORMATION:
Mixed Product Color: Black
Approximate Coverage (120 oz): 135 sq. ft. @ 5 mils
Mixing Ratio: 1:1 - DO NOT REDUCE
Cleanup: Reducer
Pot Life @ 72ºF 50% R.H.: 4 hours
Air Pressure: 50-90 psi at the gun V.O.C. (when blended 1:1) 2.28 lbs/gal. or 273 grams/liter
Recommended coats: 1 coat to coverage